Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Chimney Company in Clearwater, FL
Chimney work in Clearwater rarely looks like the pictures in a sweeping manual. Most of the fireplaces here are decorative or gas inserts in ranch and block homes built between the 1950s and 1970s, and the real enemy is salt air, not soot. Salt spray off the Gulf pits chimney caps and rusts dampers and firebox metal, while hurricane-season rain drives into masonry stacks and shows up later as efflorescence or a damper that will not turn. Our technicians have up to 15 years of experience with exactly this kind of damage. Call (844) 989-2870 for a free estimate on repair, relining, or a full inspection.
Why Clearwater Homes Are Different
Start with the housing. Clearwater’s older neighborhoods are full of 1950s to 1970s ranch and block homes, and many still have the original single-wythe brick fireplace, sometimes with a gas insert dropped in later. Those fireboxes were never built for decades of humid, salty air. Dampers seize, mortar joints crumble, and the inside of the flue quietly softens.
Then add the climate. Clearwater’s humid subtropical weather, salty Gulf breezes, intense summer thunderstorms, and wind-driven rain during hurricane season push water into masonry stacks from every direction. Efflorescence on the exterior brick is the visible sign; a rusted damper is the sign you only find once someone opens the firebox door.
The beach neighborhoods are their own story. In Clearwater Beach and Sand Key, chimney caps pit and rust through within a few years of salt spray. Many of those “fireplaces” have never held a real fire, so cleaning means pulling rust, animal nests, and moisture, not creosote. The work shifts from sweeping to corrosion inspection and water-intrusion checks.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Our Main Clearwater Services
Two jobs bring Clearwater homeowners to the phone most often: a full chimney sweep and dryer vent cleaning.
Chimney Sweep in Clearwater
A sweep here starts with a camera inspection, because the inside of a Clearwater flue tells a different story than the outside. On gas inserts and decorative fireplaces, we’re looking for rust flakes, bird nests, and moisture rather than heavy creosote. On the wood-burning fireplaces in older ranch homes, we’re checking the damper, the mortar joints, and the flue lining for the slow damage that humid air causes. You get a flat price agreed before we book. For the full scope, see Chimney Sweep in Clearwater, including what a camera inspection and photo report actually cover.
Dryer Vent Cleaning in Clearwater
Lint packed into a dryer duct is a fire waiting for a date, and Clearwater’s humid air makes it worse: lint clumps and sticks to damp duct walls instead of blowing clear. We run a brush and vacuum through the full run from the dryer to the outside vent, check the exterior flap, and confirm airflow with a meter. If the vent run is long or kinked, we say so plainly. Details on scheduling and what we check are on Dryer Vent Cleaning in Clearwater.
Chimney Repair in Clearwater
Chimney repair in Clearwater is mostly a corrosion and water problem, not a fire-damage problem. The 1950s to 1970s ranch and block homes here often still carry their original single-wythe brick firebox, and decades of salty Gulf air and humid summers have rusted the dampers and softened the mortar joints. Wind-driven rain during hurricane season finds every crack in a masonry stack. Our Chimney Repair work starts with a camera inspection, so nothing gets recommended that you can’t see in the photo report yourself. We handle the full scope, from caps and crowns to DuraFlex relining and HeatShield flue resurfacing.
Chimney Cap Installation
Signs you need it
You need a cap when the flue is open to the sky, which lets rain straight in and gives birds and squirrels a way into the stack.
What it costs in Clearwater
Chimney cap installation typically runs $150 to $450 in Clearwater, depending on the flue size and cap type.
How we do it
We measure the flue, fit a Gelco or Famco cap with the correct mesh and clearance, and fasten it to the crown so it sheds water away from the masonry.
Chimney Cap Replacement
Signs you need it
Look for rust-through, holes in the mesh, or a cap sitting loose on the crown, which is common in Clearwater Beach and Sand Key where salt spray eats metal fast.
What it costs in Clearwater
A chimney cap replacement is typically $175 to $500 in Clearwater, based on the cap material and the condition of the crown it sits on.
How we do it
We cut the old fasteners, clear the rusted cap, inspect the crown for damage, and set a new stainless or copper cap squared and sealed to the flue.
Chimney Liner Installation
Signs you need it
A cracked, rusted-through, or oversized flue is the signal, and a camera inspection on an older Clearwater home usually shows it before anything else does.
What it costs in Clearwater
Chimney liner installation typically falls between $1,800 and $4,500 in Clearwater, and the written estimate sets the final price once the flue is measured.
How we do it
We size the liner to the appliance, run a DuraFlex system down the flue, connect it at top and bottom, and insulate where the clearance calls for it.
Chimney Flashing Repair
Signs you need it
Water stains on the ceiling near the chimney, a loose flashing edge, or rust streaks down the stack point to flashing repair.
What it costs in Clearwater
Flashing repair usually costs $200 to $600 in Clearwater, depending on whether the flashing can be resealed or has to be rebuilt.
How we do it
We reset the flashing into the chimney mortar joint, seal the roof side, and check the counter-flashing so wind-driven rain runs away instead of in.
Chimney Crown Repair
Signs you need it
A cracked or crumbling crown, or efflorescence blooming down the exterior brick, says water is getting past the top of the stack.
What it costs in Clearwater
Chimney crown repair typically runs $250 to $700 in Clearwater, and a full rebuild sits at the higher end after hurricane-season damage.
How we do it
We remove the loose crown material, form a fresh overhang with the right slope away from the flue, and seal it so the masonry below stays dry.
What Chimney Repair Costs in Clearwater
| Item | Typical range in Clearwater |
|---|---|
| Chimney cap installation | $150 – $450 |
| Chimney cap replacement | $175 – $500 |
| Chimney liner installation | $1,800 – $4,500 |
| Chimney flashing repair | $200 – $600 |
| Chimney crown repair | $250 – $700 |
Do I really need a new liner?
Only if the camera shows a cracked, rusted-through, or badly oversized flue. When conditions allow, HeatShield resurfacing repairs a deteriorating flue interior without a full liner replacement, which saves cost and disruption. You see the footage before you decide. Call (844) 989-2870 for an exact quote; estimates are free.
How much does chimney repair cost in Clearwater?
Most Clearwater chimney repairs land between $150 and $4,500 depending on scope, from a cap at the low end to a full DuraFlex reline at the top. Salt-air corrosion and water intrusion drive most of the work. Call (844) 989-2870 for an exact quote; estimates are free.
Brands We Service in Clearwater
We work with professional-grade materials from the brands chimney contractors trust: DuraFlex liner systems, HeatShield flue resurfacing, Gelco and Famco caps and vent components, Olympia Chimney, and Copperfield. Liner orders are sized and placed to fit your flue, with measurable progress from the dated inspection report, so we can tell you each step and keep the job moving instead of guessing at parts. You can see the full list on our brands page.
See the difference
Before
After
Before
After
Before
AfterPricing for Chimney Company in Clearwater, FL
| Service | Typical range in Clearwater |
|---|---|
| Chimney sweep | $99 – $250 |
| Chimney cap installation | $150 – $450 |
| Chimney cap replacement | $175 – $500 |
| Chimney liner installation | $1,800 – $4,500 |
| Chimney flashing repair | $200 – $600 |
| Chimney crown repair | $250 – $700 |
| Dryer vent cleaning | $99 – $200 |
What pushes a chimney repair price up in Clearwater is access and the depth of the damage: beachfront homes with rusted-through caps, older brick fireboxes with softened mortar, and any job that needs a new liner rather than a resurface. Every price starts as a flat quote agreed before we book, and the written estimate sets the final number once the inspection is done.
Neighborhoods We Serve in Clearwater
We cover the whole of Clearwater, from the mainland ranch neighborhoods to the beach side. Salt damage is worse near the water, but the older brick fireboxes inland have their own water problems from summer storms, so the inspection is the same wherever you are. Response across Clearwater runs on the same schedule, so book early if you want a slot before burning season.
- Clearwater Beach
- Sand Key
- Countryside
- Downtown Clearwater
- Morningside
Service Area – Cities Near Clearwater
Clearwater sits at the center of a stretch of Pinellas County where the same salt air and older housing stock shape the work. We also serve homeowners in Dunedin, FL, just up the coast, and South Highpoint, FL to the east near the bay. South of us, we cover Bardmoor, FL and Largo, FL, where the ranch homes date from the same era and often show the same rusted dampers and deteriorating mortar. Wherever you are in this part of the county, the approach does not change: camera inspection first, photo report you can see, then a flat quote before anyone books the job.
Serving Clearwater, FL – Our Local Coverage Area
We serve Clearwater and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Chimney Company in Clearwater
Crews run Sunday through Friday, and the sooner you call the sooner we can fit you in. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (844) 989-2870 for a free estimate.
Some structural chimney work needs a permit, and if you’re in a Clearwater HOA or a condo with shared venting, the association may have rules too. Ask your city’s building department and your HOA before work starts; we’ll tell you what the job involves so you know what to ask.
Yes. We serve all of Clearwater, from Clearwater Beach and Sand Key to Countryside and Downtown Clearwater, plus the nearby cities in our service area. The salt-air and rain conditions differ across town, so the inspection report tells you what your specific chimney needs.
If your chimney or dryer vent needs attention in Clearwater, call (844) 989-2870. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Estimates are free, the written quote sets the price, and you’ll see the camera evidence before anything gets recommended. Written by the team at Charter Chimney Sweep.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local chimney cleaning pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Clearwater Customers Say
"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Marcy Sutton"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."
- Todd Ziegler"Liner was cracked in two places. He walked me through the repair options honestly, including the one that was cheaper for him and better for me."
- Alicia Ingram